A Checklist for Choosing a Production Line Hipot Tester

Reading Time: 8 min
Three appliances on a circular conveyor roller line in a factory, ready for production line hipot testing

If you need a hipot tester for a new production line, or to replace one that has stopped working, you will find many models that look much alike on paper. We are EEC Huayi, and we have made electrical safety testers since 1978 for manufacturers across Asia. In this checklist we set out what to confirm before you buy a production line hipot tester, so that the one you choose is accepted at audit and suits the people who use it every day. If you are still deciding which tests your products need, our guide to AC, DC and insulation resistance testing is the place to start.

To choose a production line hipot tester, start from your written test specification and confirm that the tester can run every test in it, at the voltage and current your products need. Then check how operators set and lock tests, where the tester is serviced and calibrated, and what the warranty and return terms cover.

These are the nine questions we would ask about any production line hipot tester, whichever brand you are considering.

  • Can the tester run every test listed in the certification report or the customer’s specification?
  • Does its output reach the highest test voltage the products need, with some margin left for new products?
  • Can it supply enough AC current for products with filter capacitors or heating elements, which draw current even when they are sound?
  • Can enough test programs be stored to cover every product type on the line?
  • Can the settings be locked so that operators cannot change the voltage or the limits?
  • Can a test be started, and the pass or fail result read, by the line’s PLC if the tester will sit in an automated station?
  • Where will the tester be calibrated, and how long will it be away from the line?
  • How long is the warranty, where are repairs carried out, and can the tester be returned if it does not suit the line?
  • How soon can the tester be delivered, especially if it is replacing one that has failed?

Information to Prepare Before Comparing Hipot Testers

If you prepare two documents before you speak to suppliers, you can compare their answers on the same terms, and you’re much less likely to buy the wrong tester.

The Written Production Test Specification

If your products are certified, the production test conditions usually come from your certification agency’s report or from your customer. The document names the tests and their conditions (voltage, test time and pass limits), and every other point on this checklist follows from it. If you have taken over the testing job and can’t find it, we recommend asking your quality department or the certification agency for the production test section of the report. The standards table in our AC, DC and insulation resistance guide is a useful reference, but your own specification is the one your auditor will check.

A List of Current and Planned Products to Be Tested

It helps to write down every product the tester will check, with its highest test voltage, whether it has a protective earth conductor, and whether it contains filter capacitors or heating elements. Your most demanding product decides the tester you need, even if you make it only in small numbers. We also recommend including the products you expect to make in the next two or three years, since a tester tends to stay on a line far longer than any one product does.


Matching the Tester’s Functions and Output to the Product Requirements

We would check the test functions before anything else, because a tester that can’t run one of the tests in your specification would mean buying a second instrument.

Test Functions Required by the Specification

Most production lines need some combination of AC withstand, DC withstand, insulation resistance and ground bond. Products with a protective earth conductor (Class I products) usually need a ground bond test as well as a hipot test, and our article on whether an appliance line needs a hipot tester with ground bond explains how to tell.

Output Voltage and Current Rating

You should check the highest output voltage and current against your most demanding product, and allow some margin for products you haven’t designed yet. Products with filter capacitors or heating elements draw a normal current during an AC withstand test even when their insulation is sound, and the tester must supply that current without tripping. If you have a tester on the line now, the readings it shows on good units are the best guide to the current you’ll need.

The EEC-41 runs AC withstand up to 3 kV at 100 mA, DC withstand up to 4 kV at 5 mA and insulation resistance at 1 kV (measuring up to 1,000 MΩ), and adds a ground bond test from 1.0 to 32.0 A for products with a protective earth.


Operator Controls, Settings Security and Line Integration

On a production line, the tester may be used by several operators across different shifts, and each of them needs to select the correct test and read the result without error.

Stored Test Programs and Operator Training

We would suggest asking each supplier to show you how an operator starts a test, recalls a stored program and reads a result. The EEC-31 and EEC-41 each store three test programs, so an operator can switch between product types without entering settings by hand, and the controls are designed so that an operator can be trained in minutes. If your line makes more than three product types with different settings, we recommend telling us before you buy, and we’ll tell you plainly whether three stored programs will be enough.

Security Modes to Prevent Changes to Test Settings

Another point to raise with suppliers is whether the tester can stop operators from changing the settings. If a voltage or limit is adjusted by an operator, this could allow a faulty product to pass, and this may not be picked up rapidly, potentially allowing faulty products to pass. Both of our testers have Run Only and Memory Lock security modes for this purpose.

PLC Remote Control for Automated Test Stations

If the tester will sit in an automated station, you’ll want to confirm that your PLC can start a test and read the pass or fail result. Both models accept PLC remote control, and our article on PLC control for hipot testers lists the start, reset and result signals that a typical station uses.


Calibration, Service and Running Costs of a Production Line Hipot Tester

Calibration and maintenance times impact your production line, so verifying the services provided before purchase, along with the turnaround times, is advisable.

Calibration Certificates and Laboratory Accreditation

We recommend asking where the tester will be calibrated, how long it will be away from the line, and whether the certificate comes from a laboratory accredited to ISO/IEC 17025. According to ILAC, calibration results from laboratories accredited by a signatory to its Mutual Recognition Arrangement are accepted by the other signatories, which helps if your customers are in other countries. We calibrate the EEC-31 and EEC-41 in Taiwan and Malaysia, so your tester stays in the region, and our article on how often a hipot tester needs calibration explains the interval and the daily checks.

Warranty Terms and Return Policy

Calibration, repairs and the time a tester spends away from your line all add to what it costs you over its working life, so we recommend asking about them before you compare prices.

We recommend checking how long the warranty lasts and where the supplier carries out warranty repairs. The EEC-31 and EEC-41 carry a one-year warranty with service in the Asia-Pacific region. We don’t offer an extended warranty, and we would rather you knew that before you buy; after the first year, regular calibration is what keeps the tester accurate. If one of our testers turns out not to suit your line, you can return it within 45 days under our unconditional return policy.

Purchase Price Relative to the Number of Test Functions

A fair comparison looks at what each tester costs for the functions you need. At our November 2026 list prices, the EEC-31 costs USD 899 for three test functions and the EEC-41 costs USD 2,099 for four. If your products need both hipot and ground bond, one instrument that runs both also means one calibration certificate to renew each year instead of two.

Delivery Lead Time When Replacing a Failed Tester

If you’re replacing a tester that has failed, ask whether the model is in stock in your region and when it can arrive. A lower price is of little help if your line waits weeks for the tester. When you get in touch, we would advise giving us the date you need it by, and we’ll confirm what we can supply.

If you send us your test specification, or the production test section of your certification report, with a list of the products on your line, our sales team will tell you which of our testers can run every test in it. If neither can, we’ll tell you that too. You can reach us through our contact page, or through the WhatsApp and LINE links on our website.


Frequently Asked Questions

What should I check before buying a hipot tester for my production line?

Before you buy a hipot tester for a production line, confirm that it covers every test in your certification report or customer specification, with enough voltage and current for your most demanding product. Operator controls, calibration, warranty and delivery come next. If you send EEC Huayi your specification, we'll check it against the EEC-31 and EEC-41.

How much AC current does a production line hipot tester need?

The AC current a hipot tester needs depends on your products. Products with filter capacitors or heating elements draw current during an AC withstand test even when their insulation is sound, so the tester must supply more than that normal current. The EEC Huayi EEC-31 supplies up to 10 mA at 3 kV, and the EEC-41 supplies up to 100 mA. If you already have a tester on the line, its readings on good units are a useful guide.

How long does it take to train an operator on a hipot tester?

Training time for a hipot tester depends mostly on its controls and on whether settings are stored. The EEC Huayi EEC-31 and EEC-41 are designed so that operators can be trained in minutes, and their three stored test programs mean operators don't enter settings by hand. We would suggest asking any supplier to show you the operator routine before you buy.

How quickly can I replace a hipot tester that has failed on my line?

How quickly you can replace a failed hipot tester depends on whether the model is in stock in your region. Ask the supplier for a delivery date before you compare prices, since a stopped line can cost more than the difference in price between two testers. If you contact EEC Huayi, we recommend giving us the date you need the tester by, and we'll confirm what we can supply.


If you’re ready to compare testers against your own specification, get in touch with EEC Huayi support, and our sales team will tell you which of our testers can run every test your products need.